Delta N081935 Manuale delle Istruzioni Pagina 10
- Pagina / 68
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
10
Fig. 12
Y
X
Fig. 13
Z
ASSEMBLING HEADSTOCK
TO COLUMN AND BASE
To assemble the headstock to the column:
1. Place the drill press head (P) Fig. 9 on the column as far
as it will go.
NOTE: Be sure the head-locking screws (R) are do not
block the drill press head from fully seating on the column.
To reduce the risk of injury, always use at
least two people when lifting.
2. Align the head (P) Fig. 10 with the table (Q) and the
base (B).
3. Tighten the two head-locking screws (R) Fig. 9 with the
5 mm hex wrench supplied.
INSTALLING THE CHUCK
To reduce the risk of injury, turn unit off
and disconnect it from power source before installing
and removing accessories, before adjusting or when
making repairs. An accidental start-up can cause injury.
IMPORTANT: Make certain that the tapered hole in the
bottom of spindle (U) Fig. 11, and the taper on the spindle
adapter (V) are clean and free of grease, lacquer or rust-
preventive coatings.
NOTE: Remove the rust-preventative oil from the chuck
using a soft cloth moistened with mineral spirits, paint
thinner or denatured alcohol.
Push the spindle adapter (V) Fig. 11 into the spindle (U).
making certain that the tang (W) engages the mating slot
inside the spindle (U).
NOTICE
RISK OF PROPERTY DAMAGE. To avoid
damage to the laser, prevent the cleaning solution from
coming in contact with the laser pod. You can clean the
laser pod with a dry cotton cloth.
IMPORTANT: Make certain the spindle taper (X) Fig. 12, and
tapered hole in chuck (Y) are clean and free of any grease,
lacquer or rust preventive coatings.
NOTE: Remove the rust-preventative oil from the chuck
using a soft cloth moistened with mineral spirits, paint
thinner or denatured alcohol.
IMPORTANT: Rotate the chuck until the chuck jaws are
fully retracted inside the chuck. Hold the chuck on the taper
of the spindle. Tap it with a soft-tip hammer (Z) Fig. 13 or a
block of wood and hammer to set the chuck.
NOTICE
RISK OF PROPERTY DAMAGE. To avoid
damage to the chuck, NEVER drive the chuck on the spindle
with a metal hammer.
Fig. 11
U
V
W
P
Fig. 9
R
P
Fig. 10
Q
B
- 18" (457 mm) 1
- DRILL PRESS 1
- WITH LASERS 1
- TABLE OF CONTENTS 2
- IMPORTANT SAFETY INSTRUCTIONS 2
- GENERAL SAFETY RULES 3
- SAVE THESE INSTRUCTIONS 4
- POWER CONNECTIONS 5
- MOTOR SPECIFICATIONS 5
- GROUNDING INSTRUCTIONS 5
- FUNCTIONAL DESCRIPTION 6
- CARTON CONTENTS 7
- 24" (610 mm) MINIMUM 8
- ASSEMBLING DRILL PRESS PARTS 9
- ASSEMBLING HEADSTOCK 10
- TO COLUMN AND BASE 10
- INSTALLING THE CHUCK 10
- ATTACHING THE 11
- LED WORK LIGHT 11
- CHUCK KEY STORAGE 11
- TABLE LOCKING WRENCH STORAGE 12
- BELT TENSION LEVER HANDLE 12
- TABLE INSERT 12
- OPERATIONAL CONTROLS AND 13
- ADJUSTMENTS 13
- TABLE ADJUSTMENTS 14
- ADJUSTING THE SPINDLE RETURN 15
- CHECKING LASER ADJUSTMENT 16
- SPINDLE SPEEDS 17
- MACHINE USE 19
- CORRECT DRILLING SPEEDS 20
- DRILLING WOOD 20
- TROUBLESHOOTING 21
- MAINTENANCE 21
- ACCESSORIES 22
- WARRANTY 22
- RÈGLES DE SÉCURITÉ GÉNÉRALES 24
- CONSERVER CES DIRECTIVES 25
- Ouvertures laser 26
- RACCORDEMENTS ÉLECTRIQUES 27
- SPÉCIFICATIONS DU MOTEUR 27
- DESCRIPTION FONCTIONNELLE 28
- CONTENUS DE BOITE 29
- 24" 30
- (610 mm) 30
- ASSEMBLAGE DE LA PERCEUSE À 31
- LA COLONNE ET LA BASE 32
- INSTALLATION DU MANDRIN 32
- PLAQUETTE 34
- FONCTIONNEMENT 35
- RÉGLAGES DE LA TABLE 36
- ÉLEVER ET ABAISSER LA BROCHE 37
- VÉRIFICATION DU RÉGLAGE LASER 38
- VITESSE DE LA BROCHE 39
- LA TENSION DE COURROIE 40
- UTILISATION DE LA MACHINE 41
- RETRAIT DU MANDRIN ET DE 42
- L’ADAPTATEUR DE BROCHE 42
- VITESSES ADÉQUATES DE PERÇAGE 42
- PERÇAGE DU BOIS 42
- PERÇAGE DU MÉTAL 42
- ENTRETIEN 43
- DEPANNAGE 43
- ACCESSOIRIES 44
- GARANTIE 44
- NORMAS GENERALES DE SEGURIDAD 46
- GUARDE ESTAS INSTRUCCIONES 47
- ESPECIFICACIONES DEL LÁSER 48
- ESPECIFICACIONES DEL MOTOR 49
- DESCRIPCIÓN FUNCIONAL 50
- CONTENIDO DE CARTON 51
- (610 mm) MÍNIMO 52
- PRENSA DE TALADRO 53
- ENSAMBLAJE DEL CABEZAL 54
- A LA COLUMNA Y LA BASE 54
- INSTALACIÓN DEL PORTABROCAS 54
- FIJAR LA MESA 56
- LA CORREA 56
- ENCASTRE PARA LA MESA 56
- OPERACIÓN 57
- AJUSTES A LA MESA 58
- REVISIÓN DEL AJUSTE DEL LÁSER 60
- VELOCIDADES DEL HUSILLO 61
- LA TENSIÓN DE LA CORREA 62
- UTILIZAR LA MAQUINA 63
- MANTENIMIENTO 65
- LOCALIZACION DE FALLAS 65
- SERVICIO 66
- ACCESORIOS 66
- PÓLIZA DE GARANTÍA 67
- GARANTIA 68
Philips For Kids Cabezal de cepillado Sonicare estándar manuály
Uživatelské manuály a uživatelské příručky pro Zdraví a hygiena Philips For Kids Cabezal de cepillado Sonicare estándar.
Poskytujeme 1 manuály pdf Philips For Kids Cabezal de cepillado Sonicare estándar ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commenti su questo manuale