Delta BS100 Manuale delle Istruzioni

INSTRUCTION MANUAL9" Bench Band Saw(Model BS100)PART NO. A03049 - 03-05-04Copyright © 2004 Delta MachineryESPAÑOL: PÁGINA 25To learn more about D

101. Fasten the lamp bracket (A) Fig. 13, to the top coverof the machine, using two M6x1x12mm cap headscrews (B) and 1/4" lockwashers as shown.2.

11OPERATING CONTROLS AND ADJUSTMENTSFig. 15Fig. 16Fig. 17STARTING ANDSTOPPING SAWThe switch (A) Fig. 15, is located on the front side of theband saw.

12Fig. 19ADJUSTINGBLADE TENSIONBlades of 1/8", 1/4", and 3/8" in width by 59-1/2" inlength are available for use with your band sa

13ADJUSTING UPPER BLADEGUIDES AND BLADESUPPORT BEARINGIMPORTANT: BOTH THE UPPER AND LOWERBLADE GUIDES MUST BE PROPERLY ADJUSTEDTO PREVENT THE BLADE FR

14ADJUSTING LOWER BLADEGUIDES AND BLADESUPPORT BEARINGThe lower blade guides and blade support bearingshould be adjusted at the same time as the upper

15ADJUSTING THE TABLEPOSITIVE STOPSPositive stops are provided for the table at the 90 and 45degree angle to the blade. To check and adjust thepositiv

16Fig. 37AWRENCH STORAGEThe 3mm and 4mm wrenches (A) supplied with yourband saw can be stored inside the wheel cover asshown in Fig. 37A.ACHANGING BLA

17Before starting the machine, see that all adjustments are properly made and the guards are in place. Turn the upperwheel by hand to make sure that e

18Fig. 40Fig. 40 illustrates a typical bevel cutting operation using the accessory miter gage.Fig. 41Fig. 41 illustrates a typical resawing applicatio

19In spite of how well a band saw is maintained, problems can occur. The following troubleshootingguide will help you solve the more common problems:T

2Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

20Trouble: BLADE WILL NOT TRACK.Probable CauseRemedy1. Blade too loose 1. Adjust tension2. Upper wheel not properly adjusted. 2. Adjust upper wheel.3.

21BAND SAW BLADESA band saw blade is a delicate piece of steel that is subjected to tremendous strain. You canobtain long use from a band saw blade if

22NOTES

23NOTES

24PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

The following are trademarks of PORTER-CABLE·DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,BAMMER®, B.O.S.S.®, Builder

3GENERAL SAFETY RULES1. FOR YOUR OWN SAFETY, READ THE INSTRUC-TION MANUAL BEFORE OPERATING THEMACHINE. Learning the machine’s application,limitations,

4ADDITIONAL SAFETY RULES FORBAND SAWS1. DO NOT OPERATE THIS MACHINE UNTIL it isassembled and installed according to theinstructions.2. OBTAIN ADVICE f

5A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and shouldbe protected with a 20 Amp ti

6EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wireextension cord which has a 3-prong groun

79" BENCH BAND SAW PARTS1 - Band Saw2 - Lamp3 - Lamp Cord Clamps(2)4 - 1/4" Lockwashers (2)5 - M6x1x12mm Cap Head Screws (2)Fig. 26 - Table7

8ASSEMBLYFig. 4ASSEMBLING TABLETO MACHINE1. Locate table locking lever (shown disassembled)Fig. 4, M10 flat washer (B) and 4mm wrench (C).2. Using the

9Fig. 9Fig. 10Fig. 116. Locate pinion knob (N) Fig. 9, spring (O), and specialscrew (P).7. Position pinion knob (N) Fig. 10, onto the back ofsaw so th