Delta 36-714 Manuale Utente

INSTRUCTION MANUALDelta 10" Hybrid Saw(Model 36-714) PART NO. A15973 - 12-15-05Copyright © 2005 Delta MachineryNOTE: Shown with BC30 30” Bieseme

10SETTING UP YOUR SAWThe 36-714 comes with a mobile base which can be used by attaching the mobile base pedal as shown below. If desired, the saw can

11BLADE TILTING AND RAISING HANDWHEELSPlace blade tilting handwheel (A) Fig. 7A on shaft (B) on the left side of the saw cabinet. Make certain slot (C

12Fig. 10Assemble left extension wing (A) Fig. 10A to the saw table. Align the three holes in the extension wing with the three holes (A) Fig. 9 in th

13INSTALLING THE SWITCH1. Place switch (A) Fig. 11, behind the lip of extension wing (B). Insert M8x30 hex head screw (C) through wing and then switch

14ASSEMBLING BLADE GUARD ANDSPLITTER Make sure blade is not attached. If it is, remove the saw blade from the saw using the supplied wrenches.1. Fast

156. If alignment is necessary, loosen the two screws(F) Fig. 18, align bracket (D) with the inner arbor flange (E), and tighten screws (F).7. Loose

16SAW BLADE Disconnect machine from power source.1. Raise the saw blade arbor to its maximum height. Assemble the saw blade (C) Fig. 23 to the saw ar

17Fig. 26LPINSTALLING TABLE INSERT Disconnect machine from power source.Lower saw blade and install table insert (P) Fig. 26, in the saw table. IMPORT

18ASSEMBLING MITER GAGE Disconnect machine from power source.Place a flat washer (A) Fig 30 on the threads of the miter gage lock handle (B) and then

19Fig. 33CFig. 34EDADJUSTING 90 DEGREE AND 45 DEGREE POSITIVE STOPSThe machine is equipped with positive stops that will quickly and accurately positi

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. When using tools or equipment, basi

20Fig. 38ABDCBACKLASH ADJUSTMENTS Disconnect machine from power source.After a period of extended use, if any play is detected in the blade raising o

21MITER GAGE OPERATION AND ADJUSTMENTThe miter gage is equipped with adjustable index stops at 90, 75, 60,45 and 30 degrees.To rotate the miter gage,

22KEY PARTS AND SAFETY FEATURES ON YOUR SAWBACK VIEW13. Fence Holders14. Motor Cover15. Dust Spout16. Slide Plate17. Mobile Base Foot Pedal18. Bl

23CROSS-CUTTINGCross-cutting requires the use of the miter gauge to posi-tion and guide the work. Before starting the cut, raise the blade so it is ab

24Never use the fence as a cut-off gauge when cross-cutting.When cross-cutting a number of pieces to the same length, a block of wood (B), can be clam

25Fig. S8Fig. S9AFig. S10Ripping, as shown in Fig. S8, is cutting lengthwise through a board. The rip fence (A) is used to position and guide the work

26BEVEL RIPPINGBevel ripping (as shown in Fig. S12) is the same as ripping except the bevel angle is set to an angle other than 0 degrees. When possib

27Fig. S15NOTE: The outside arbor flange can not be used with the moulding cutterhead. Tighten the arbor nut against the cutterhead body. do not lose

28Fig. S20Fig. S18 Fig. S191. Dadoing is cutting a rabbet or wide groove into the work. Most dado head sets are made up of two outside saws and four

29CONSTRUCTING A FEATHERBOARDFig. S23, illustrates dimensions for making a typical featherboard. The material which the featherboard is constructed of

3It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. Th

30When ripping work less than 6 inches wide, a push stick should be used to complete the feed and could easily be made from scrap material by followin

31MAINTENANCEKEEP MACHINE CLEANPeriodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cl

Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine a

The following are trademarks of PORTER-CABLE • DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marques suivantes sont

41. FOR YOUR OWN SAFETY, READ THE INSTRUCTION MANUAL BEFORE OPERATING THE MACHINE. Learning the machine’s application, limitations, and specific haza

5Failure to follow these rules may result in serious personal injury.ADDITIONAL SPECIFIC SAFETY RULESSAVE THESE INSTRUCTIONS. Refer to them often and

6A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp t

EXTENSION CORDSUse proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong groun

CARTON CONTENTS Fig. 1 Parts1. Cast Iron Extension Wings (2)2. Switch Assembly3. Fence Holder Brackets (2)4. Drive Belt5. Table Insert6. Wr

9ASSEMBLYASSEMBLY TOOLS REQUIRED* Phillips head screw driver (not supplied)* ½”, 13mm, 5/8”, 3/8” open end wrenches (not supplied)* Other wrenches and