Delta 34-814 Manuale delle Istruzioni

INSTRUCTION MANUALPART NO. 422-04-651-0064 - 06-20-05Copyright © 2005 Delta MachineryTo learn more about DELTA MACHINERY visit our website at: www.del

101. The Magnetic Starter on/off switch (A) Fig. 9 comesattached to a mounting bracket on the right side ofthe machine. Remove it.2. Insert a 5/16-18x

113. To check the alignment, remove the screw andfastener plate (C) Fig. 13. Use a straight edge (D) Fig.14 to see if the splitter bracket (A) is alig

128. Use a 5/16-18x1" hex head bolt (N) with 5/16"lockwasher and 5/16" flat washer to attach the uppersplitter bracket (M) Fig. 20 to t

1312. Use a straight edge (A) Fig. 25 to make certain thatthe splitter (P) is aligned with the saw blade (B). Usea square (C) Figs. 27 and 28 to make

14Use four #10 x 1/2" sheet metal screws to attach the ripfence holder brackets (A) and (B) Fig. 33 to the four holeslocated in the left hand sid

15Raise or lower the saw blade with the front handwheel (A)Fig. 41. With the exception of hollow ground blades, raisethe blade 1/8" to 1/4"

161. Raise the saw blade to its highest position.2. Set the blade at 90° to the table by turning the blade tilting handwheel counterclockwise as far a

Insert the miter gauge bar into the miter gauge slot on the table. Attach the washer and lock handle (A) Fig. 43 to themiter gauge bar.The miter gauge

18MACHINE USECOMMON SAWING OPERATIONSCommon sawing operations include ripping and crosscutting plus a few other standard operations of a fundamental n

19RIPPINGRipping is cutting lengthwise through a board, (Fig. 49).NOTE: Be sure the material to be cut is seasoned, dry andflat. The rip fence (A) is

2TABLE OF CONTENTSRead and understand all warnings and operating instructions before using any tool or equipment. Whenusing tools or equipment, basic

20When ripping material with a veneer facing that extendsover the material, the fence (A) should be in the horizontalposition with the veneer (B) exte

21USING MOULDING CUTTERHEADMoulding is cutting a shape on the edge or face of the work.Cutting mouldings with a moulding cutterhead is a fast, safeand

1. Dadoing is cutting a rabbet or wide groove into thework. Most dado head sets are made up of two outsidesaws and four or five inside cutters, (Fig.

23USING AUXILIARY WOOD FACING ON RIP FENCEWhen performing special cutting operations – and thatoperation may cause the cutting implement to contactthe

24PUSH STICKMAKE FROM 1/2" OR 3/4"WOOD OR THICKNESSLESS THAN WIDTH OFMAT’L. TO BE CUTCUT OFF HERE TOPUSH 1/4" WOODCUT OFF HERE TOPUSH 1

25TROUBLESHOOTINGFor assistance with your machine, visit our website at www.deltamachinery.comfor a list of service centers or callthe DELTA Machinery

26PARTS, SERVICE OR WARRANTY ASSISTANCEAll Delta Machines and accessories are manufactured to high quality standards and are serviced by a networkof P

27Two Year Limited New Product WarrantyDelta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine

The following are trademarks of PORTER-CABLE •DELTA (Las siguientes son marcas registradas de PORTER-CABLE • DELTA S.A.) (Les marquessuivantes sont de

3Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.Indicates a potentially hazardous situation

4GENERAL SAFETY RULESREAD AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFOREUSING THIS EQUIPMENT. Failure to follow all instructions listed

5ADDITIONAL SPECIFIC SAFETY RULES1. DO NOT OPERATE THIS MACHINE until it isassembled and installed according to theinstructions.2. OBTAIN ADVICE FROM

6GROUNDING INSTRUCTIONSTHIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROMELECTRIC SHOCK.Permanently connected machines:If the mac

73. DUST CHUTE ADAPTER4. HANDWHEEL5. BLADE GUARD AND SPLITTER BRACKET6. MITER GAUGE7. EXTENSION WING8. HANGERS FOR RIP FENCE (2)9. CLOSED-END ARBOR WR

81. Install the fiber washer (A) Fig. 3 on the shaft (B). Install the key (C) into the shaft keyway.2. Place the handwheel (D) on the shaft (B) Fig. 3

9Use a straight edge (C) Fig. 6 to be sure that theextension wing (A) and the saw table (D) are even witheach other before tightening the screws (B) F